|
|
|
Interferences and Clearances of Fits between Shafts and Inner Rings: f6, g5, g6, h5 -1
Part 1 | Part 2 | Part 3 | Part 4 | |
C : Clearance I : Interference Units : µm
| Size Classification (mm) |
Δdmp |
Interference or clearnce for Each Fitting Class |
f6 |
g5 |
g6 |
h5 |
C |
C |
I |
C |
I |
C |
I |
| over |
incl |
high |
low |
max |
min |
max |
max |
max |
max |
max |
max |
| 3 |
6 |
0 |
-8 |
18 |
2 |
9 |
4 |
12 |
4 |
5 |
8 |
| 6 |
10 |
0 |
-8 |
22 |
5 |
11 |
3 |
14 |
3 |
6 |
8 |
| 10 |
18 |
0 |
-8 |
27 |
8 |
14 |
2 |
17 |
2 |
8 |
8 |
| 18 |
30 |
0 |
-10 |
33 |
10 |
16 |
3 |
20 |
3 |
9 |
10 |
| 30 |
50 |
0 |
-12 |
41 |
13 |
20 |
3 |
25 |
3 |
11 |
12 |
| 50 |
65 |
0 |
-15 |
49 |
15 |
23 |
5 |
29 |
5 |
13 |
15 |
| 65 |
80 |
0 |
-15 |
49 |
15 |
23 |
5 |
29 |
5 |
13 |
15 |
| 80 |
100 |
0 |
-20 |
58 |
16 |
27 |
8 |
34 |
8 |
15 |
20 |
| 100 |
120 |
0 |
-20 |
58 |
16 |
27 |
8 |
34 |
8 |
15 |
20 |
| 120 |
140 |
0 |
-25 |
68 |
18 |
32 |
11 |
39 |
11 |
18 |
25 |
| 140 |
160 |
0 |
-25 |
68 |
18 |
32 |
11 |
39 |
11 |
18 |
25 |
| 160 |
180 |
0 |
-25 |
68 |
18 |
32 |
11 |
39 |
11 |
18 |
25 |
| 180 |
200 |
0 |
-30 |
79 |
20 |
35 |
15 |
44 |
15 |
20 |
30 |
| 200 |
225 |
0 |
-30 |
79 |
20 |
35 |
15 |
44 |
15 |
20 |
30 |
| 225 |
250 |
0 |
-30 |
79 |
20 |
35 |
15 |
44 |
15 |
20 |
30 |
| 250 |
280 |
0 |
-35 |
88 |
21 |
40 |
18 |
49 |
18 |
23 |
35 |
| 280 |
315 |
0 |
-35 |
88 |
21 |
40 |
18 |
49 |
18 |
23 |
35 |
| 315 |
355 |
0 |
-40 |
98 |
22 |
43 |
22 |
54 |
22 |
25 |
40 |
| 355 |
400 |
0 |
-40 |
98 |
22 |
43 |
22 |
54 |
22 |
25 |
40 |
| 400 |
450 |
0 |
-45 |
108 |
23 |
47 |
25 |
60 |
25 |
27 |
45 |
| 450 |
500 |
0 |
-45 |
108 |
23 |
47 |
25 |
60 |
25 |
27 |
45 |
|
|
|
